Pressure Equipment Compliance (PED)
2010/35/EU
What we certify
The Pressure Equipment Directive 2014/68/EU, known as the PED, establishes the rules for the design, manufacture and conformity assessment of all equipment operating at pressures above 0.5 bar.
What needs to be done?
The PED Directive identifies the manufacturer as the sole party responsible for the conformity of the equipment, demonstrated through:
- the preparation of the technical file,
- the preparation of the EU Declaration of Conformity,
- the affixing of the CE marking to the equipment.
In the case of Category II or higher equipment / assemblies, the manufacturer is required to engage a Notified Body, such as ECO Certificazioni, to carry out a documentary and product assessment prior to placing on the market, which may only take place after the certificate has been obtained.
We operate throughout Italy.
From North to South, we are ready to listen to you. Would you like us to call you back?
One of our sales representatives can call you with no obligation.
What are the fields of application?
The Directive Directive applies to a wide range of pressure equipment whose level of hazard, and therefore Category, depends on the combination of three factors:
- type of fluid contained,
- operating pressure,
- equipment size (nominal volume or nominal diameter).
In general, the scope includes:
- Vessels intended to contain pressurized fluids;
- Piping and pipelines for the transport of fluids;
- Pressure accessories with an operational function;
- Safety accessories that provide protection against exceeding pressure limits;
Assemblies comprising multiple items of pressure equipment.
Inspections
Lifts and lifting systems
Periodic inspections of lift installations pursuant to Presidential Decree No. 162 of 30 April 1999, as amended, implementing Directive 2014/33/EU relating to lifts and safety components for lifts, as well as to the operation of lifts.
Inspections
Inspection of electrical earthing systems
Mandatory periodic inspection of electrical earthing systems, lightning protection devices, and electrical installations in workplaces with an explosion hazard, in accordance with Presidential Decree 462/01.
Inspections
Portable ladders
Inspections of escalators and moving walkways in accordance with maintenance requirements established over time, up to the current legislation, Presidential Decree of 30 April 1999 and subsequent amendments
ECO Certificazioni S.p.A., following accreditation no. 00234, has obtained authorization from the Ministry of Enterprises and Made in Italy (MIMIT) to issue certifications, as Notified Body no. 0714, for Modules A2, B, C2, D, E, F, G, H, thus enabling the free movement of goods within the European Union.
Regulatory framework
The Directive 2010/35/EU , also known as T-PED, which replaced 1999/36/EC, establishes the rules and procedures to be followed for the certification of transportable pressure equipment.
The T-PED Directive governs the design, manufacture and conformity assessment of transportable pressure equipment, with the aim of improving its safety and ensuring its free movement within the EU market.
Conformity assessment procedures
The requirements for the products subject to assessment are defined with reference to Annex I to Directive 2008/68/EC, referred to as the ADR. The international carriage of dangerous goods by road is regulated at European level. This Agreement, consisting of a text comprising a small number of articles, includes two Annexes (Annex A and Annex B), which contain all the regulatory provisions that must be complied with for such transport.
The role of the Notified Body
ECO is a Notified Body designated by the Ministry of Infrastructure and Transport and can perform Conformity Assessment activities pursuant to T-PED Directive 2010/35/EU for the purposes of:
- approval and authorization for placing on the market newly manufactured transportable pressure equipment
- reassessment of the conformity of existing transportable pressure equipment already on the market that does not bear the conformity marking but can be reassessed against T-PED
- performing periodic inspections to verify continued compliance with the safety requirements necessary for the reuse of transportable pressure equipment.
- The issuance of the certificate is therefore subject to the completeness and correctness of the documentation file, as documented by an inspection report, and to the compliance of the product/system with the documentation assessed.
Upon completion of the inspections, inspection reports and an inspection certificate are issued, summarizing the outcome of the assessments performed and whether or not the equipment may be placed / remain in service.
In the case of new or reassessed equipment, the manufacturer affixes the π marking followed by the notification number (0714 for ECO Certificazioni).
Inspection of "legacy fleet" equipment
Legislative Decree No. 78 of 12 June 2012, transposing and implementing Directive 2010/35/EU, known as T-PED, established the regulatory framework for the approval and periodic inspection of newly manufactured transportable pressure equipment; however, previously manufactured equipment approved in accordance with the procedures established by the Royal Decree of 12 September 1925 and subsequent supplementary regulations, concerning the approval of the regulations for the testing and inspection of vessels intended for the carriage by rail of compressed, liquefied or dissolved gases, remained excluded from the scope of periodic inspections for maintaining such equipment in service. Responsibility for maintaining this equipment remained with the INAIL inspection body.
The Decree of 18 June 2015 of the Ministry of Infrastructure and Transport, with the primary aim of harmonizing activities in the field of the manufacture, approval and maintenance in service of transportable pressure equipment, authorizes third-party bodies to carry out conformity assessments, periodic inspections, intermediate inspections, exceptional inspections and supervision of the in-house inspection service for equipment, and establishes the procedures for applications for recognition by such Bodies and for granting authorization.
ECO is a Type A Inspection Body (accreditation No. 00234 ISP) and a Notified Body (No. 0714), authorized by the Ministry of Infrastructure and Transport (MIT) for the following activities:
- Certification pursuant to Annex III to Directive 2010/35/EU;
- 1.8.7.3 (ADR) Supervision of manufacture;
- 1.8.7.4 Initial inspections and tests;
- 1.8.7.6 Periodic inspections, intermediate inspections and exceptional inspections;
- 1.8.7.7 Authorization and supervision of the in-house inspection service.